Jaylor 6350, 6400, 6425, 6575 Tek Helezonlu TMR Mikserleri için PTO Mili

Jaylor Tek Helezonlu TMR Mikser Modelleri için Güvenilir PTO Mikseri

Jaylor Tek Helezonlu TMR Karıştırıcı Modelleri: 5350, 5400, 5425, 5575 için PTO Mili

The PTO shaft for Jaylor Single Auger TMR Mixers 6350, 6400, 6425, and 6575 is a precision-engineered tractor PTO drive shaft designed to transfer rotational power from your tractor directly to the mixer's feed mixer gearbox. Manufactured from high-strength alloy steel, this feed mixer PTO shaft features forged yokes, hardened universal joints, and a telescoping tube assembly that accommodates varying distances between the tractor and the vertical feed mixer. Whether you operate a mid-sized dairy farm or a large beef cattle backgrounding operation, this agricultural PTO shaft ensures consistent, uninterrupted power delivery at 540 RPM, enabling the mixer's patented square-cut auger to process bales, silage, and grain into a uniform total mixed ration with minimal sorting.

CMN Transmission engineered this PTO drive shaft for feed mixer applications where reliability and durability are non-negotiable. The shaft integrates a slip clutch overload protection system that automatically disengages when torque exceeds the rated threshold, protecting both the tractor's drivetrain and the mixer's gearbox from shock loads caused by frozen feed, tangled twine, or foreign objects. A full-length PTO shaft guard with safety chains meets CE safety standards, keeping operators protected during daily feeding routines. This PTO driveline shaft serves as a direct replacement of Bondioli & Pavesi PTO shaft assemblies, matching original spline profiles, tube diameters, and cross-and-bearing dimensions for bolt-on installation with zero modifications.

Teknik Özellikler

Ana Mil: Sabit Hızlı PTO

SFT Sabit Hız Montajları

Kesme Cıvatası Yatağı

6 Numara Kesme Cıvatası Yatağı

8 Numara Kesme Cıvatası Bağlantı Elemanları

PTO emniyet cıvatası tork sınırlayıcılarımız hakkında daha fazla bilgi için lütfen inceleyin.

Jaylor Yem Karıştırıcısı için PTO Tahrik Mili Özellikleri

1. Drop-Forged Alloy Steel Yokes
Both the tractor-end and implement-end PTO shaft yoke assemblies are drop-forged from premium alloy steel rather than cast. This forging process aligns the grain structure of the metal, providing substantially higher impact resistance and fatigue strength under the repetitive torsional loads generated during daily TMR mixing operations.

2. Integrated Slip Clutch Overload Protection
The slip clutch PTO shaft configuration automatically disengages when drivetrain torque exceeds the rated threshold of 1,200 Nm. This protects both the tractor gearbox and the Jaylor mixer's planetary gearbox from shock loads caused by frozen feed blocks, tangled bale twine, or foreign debris entering the mixing chamber during operation.

3. Heavy Duty Universal Joints
Each PTO shaft universal joint uses hardened, needle-roller bearing crosses sized specifically for Category 4 service loads. Pre-greased and sealed at the factory, these heavy duty PTO shaft U-joints maintain smooth articulation across operating angles up to 15 degrees while tolerating the continuous vibration inherent in vertical feed mixer PTO shaft applications.

4. Precision Telescoping PTO Shaft Tube
The PTO shaft tubing system uses a precision lemon-profile inner tube sliding within a matched outer tube. This design minimizes rotational backlash while retaining smooth telescoping action even after years of continuous field use. The PTO shaft tube profile allows the shaft to accommodate changes in distance as the tractor and mixer move over uneven ground.

5. Tam Boy Güvenlik Koruma Sistemi
Every assembly includes a complete PTO shaft guard and PTO shaft cover set with support chains covering the entire rotating shaft profile. Designed to meet CE and regional safety standards, the guard attaches securely at both the tractor-end and implement-end yoke flanges, keeping operators fully protected during feeding passes and preventing clothing or limb entanglement.

6. Direct Replacement Compatibility
Engineered as a direct replacement of Bondioli & Pavesi PTO shaft assemblies, this tractor PTO shaft matches original equipment spline profiles, PTO shaft dimensions, cross-and-bearing specifications, and guard designs. Operators can swap the shaft onto their Jaylor 6350, 6400, 6425, or 6575 mixer without any shimming, adapters, or modifications required.

Working Principle of the PTO Shaft for TMR Feed Mixer

The PTO shaft for Jaylor Single Auger TMR Mixers operates on a straightforward mechanical principle: it transfers rotational power from the tractor's engine to the mixer's internal auger system without requiring the mixer to carry its own independent power source. The process begins when the tractor operator engages the Power Take-Off. The tractor's PTO stub shaft, a splined output protruding from the rear of the tractor, starts rotating at a standardized 540 RPM. This is the standard 540 PTO shaft speed used across the Jaylor 6350, 6400, 6425, and 6575 single auger mixer lineup.

The tractor PTO tahrik mili connects to this rotating stub via a splined PTO shaft yoke that slides over the tractor's output spline and locks into place. From this connection point, rotational energy travels through the first PTO shaft U-joint, which redirects the power through a slight angle to accommodate the alignment offset between the tractor and the mixer hitch point. The energy then passes through the telescoping PTO shaft tube section, a lemon-profile inner tube that slides within an outer tube, allowing the shaft to lengthen or shorten as the tractor moves forward, backs up, or traverses uneven terrain.

At the implement end, the rotational force passes through a second PTO shaft universal joint and into the slip clutch assembly. The slip clutch acts as an automatic safety valve: under normal operating conditions, spring-compressed friction discs transfer full torque from the shaft to the mixer's planetary gearbox input shaft. However, if the mixer's auger encounters an obstruction such as frozen feed, wire, or a foreign object that causes torque to spike beyond the preset threshold, the clutch plates begin to slip. This allows the tractor-side and implement-side of the driveline shaft to rotate independently, absorbing the shock load rather than transmitting it through the drivetrain.

Once the torque passes through the clutch and enters the mixer's planetary gearbox, it undergoes speed reduction and torque multiplication. The gearbox converts the incoming 540 RPM into approximately 41 RPM at the auger, while dramatically increasing torque. This low-speed, high-torque output drives the Jaylor patented square-cut auger, pulling feed material downward and outward in a continuous mixing pattern that produces a uniform ration. The entire power path, from the tractor engine through the PTO drive shaft to the auger tip, forms an unbroken mechanical chain that relies on each component working in precise coordination.

Applications of the Feed Mixer PTO Shafts

1. Süt Çiftlikleri
On dairy operations, consistent TMR quality directly impacts milk production and butterfat content. This PTO shaft for TMR feed mixer powers the Jaylor single auger at a steady 540 RPM, ensuring silage, grain, minerals, and protein supplements are blended into a homogeneous ration every cycle. Dairy producers using Jaylor 6425 or 6575 mixers rely on this tractor PTO shaft to deliver uniform feed that minimizes sorting at the bunk, helping maintain stable rumen health across the entire milking herd throughout lactation.

2. Sığır Yetiştiriciliği İşletmeleri
Beef backgrounding and finishing yards demand efficient feed processing to maintain consistent average daily gain across large groups. This agricultural PTO shaft enables Jaylor 6350, 6400, 6425, and 6575 mixers to rapidly break down round and square bales and blend them with byproducts, distillers grains, and energy supplements. The slip clutch protects the drivetrain when processing tightly packed bales, while the heavy duty PTO shaft construction withstands the high-torque demands of daily batch mixing.

3. Koyun ve Keçi İşletmeleri
Sheep and goat operations frequently require finely processed rations to prevent feed waste and selective eating by smaller livestock. The vertical feed mixer PTO shaft delivers smooth, continuous power to the Jaylor auger, enabling thorough chopping and mixing of hay, pellets, and mineral premixes into a particle size appropriate for small ruminants. The Jaylor 6350 and 6400 models, powered by this 540 PTO shaft, are particularly well suited for medium-scale sheep and goat feeding programs.

4. Domuz Yetiştiriciliği
Swine producers who mix their own on-farm rations use TMR mixers to combine corn, soybean meal, premixes, and fiber sources into balanced diets for gestation, lactation, and grow-finish phases. This PTO shaft for Jaylor feed mixer provides the reliable 540 RPM power needed to drive the auger through dense, heavy feed ingredients. The integrated overload protection prevents damage when processing sticky or compacted materials, keeping the driveline safe and reducing maintenance downtime during critical feeding schedules.

5. At ve Atçılık Operasyonları
Equine feeding programs require precise ration consistency to support digestive health and performance. This PTO drive shaft for feed mixer ensures the Jaylor single auger mixer gently but thoroughly blends hay, grain, supplements, and vitamins into a uniform mix that reduces waste and prevents horses from sorting through their feed. Breeding farms, training facilities, and rescue operations with 50 or more head benefit from the consistent batch quality that this tractor PTO drive shaft delivers to the Jaylor mixing chamber.

Vertical Feed Mixer PTO Shaft Installation Steps

Adım 1: Güvenlik Hazırlığı
Park the tractor on level ground, shut off the engine completely, disengage the PTO lever, set the parking brake, and remove the ignition key. Never work near a PTO stub shaft with the engine running. Confirm the mixer is on stable, level ground and the hitch is secured. Wear close-fitting clothing and avoid loose sleeves, jewelry, or anything that could catch on rotating parts during the installation process.

Step 2: Inspect the Tractor PTO Stub Shaft
Use a wire brush to clean any corrosion, dirt, or old grease from the spline teeth on the tractor's PTO output stub. Inspect the snap-ring groove for damage. A worn or deformed groove cannot securely retain the PTO shaft yoke and must be repaired before proceeding. Apply a thin film of lithium-based grease to the spline surface.

Step 3: Connect the Tractor-End Yoke
Slide the tractor-end PTO shaft yoke onto the tractor's stub shaft. Ensure the yoke slides smoothly over the splines and that the locking mechanism (push-pin or collar) engages fully into the snap-ring groove. Pull back on the yoke to verify it is locked. If the yoke does not slide freely, do not force it. Recheck spline compatibility. This PTO shaft is configured for a standard 1 3/8" - 6 spline interface. If your tractor uses a 1 3/4" - 20 spline, order the appropriate PTO shaft adapter configuration.

Step 4: Connect the Implement-End Yoke
Raise or lower the mixer's hitch until the planetary gearbox input shaft is accessible. Clean the implement input splines with a wire brush and apply grease. Slide the implement-end yoke onto the gearbox input shaft and verify it locks into position. If your Jaylor mixer uses a shear bolt PTO shaft connection, install a new PTO shaft shear bolt of the specified grade and torque it to the manufacturer's recommendation. Never substitute a harder bolt, as this defeats the overload protection.

Step 5: Verify Operating Angle
With the mixer at its normal working position and hitched to the tractor, visually assess the angle between the tractor PTO stub and the shaft. The included angle should not exceed 15 degrees for this standard PTO shaft. Excessive angles accelerate PTO shaft U-joint bearing wear exponentially and cause premature failure. Adjust the hitch height if the angle is too steep.

Step 6: Verify Tube Overlap
Extend the hitch to maximum distance and compress it to minimum. Confirm the inner PTO shaft tube remains inside the outer tube by at least one-third of the inner tube's total length at full extension. Also confirm the tubes do not bottom out at full compression. Inadequate overlap causes the shaft to separate under load, while bottoming out can damage the tubes and yokes.

Step 7: Install the PTO Shaft Guard
Attach the PTO shaft guard halves over the rotating shaft assembly. Secure the support chains at the tractor-end and implement-end anchor points so the guard remains stationary while the shaft rotates inside it. Ensure the guard rotates freely without contacting the shaft. Replace any damaged guard sections before operating the equipment.

Step 8: Test Run
Start the tractor engine, engage the PTO at low idle speed, and observe the shaft for vibration, unusual noise, or wobble. Increase to full operating speed (540 RPM) gradually. Monitor for the first 10 minutes while the auger runs empty to confirm smooth operation before loading feed material into the mixer.

Tractor PTO Shaft Components

• Tractor-End Yoke (Inner Yoke)
  The tractor-end PTO shaft yoke is the splined coupling that slides onto the tractor's PTO stub shaft. Drop-forged from alloy steel, it features an internal spline profile (1 3/8" - 6 spline standard) and a push-pin locking collar that snaps into the tractor's snap-ring groove. This yoke transmits the full rotational output of the tractor engine into the driveline shaft assembly.
• Implement-End Yoke (Outer Yoke)
  The implement-end PTO shaft yoke connects to the Jaylor mixer's planetary gearbox input shaft. Also drop-forged from alloy steel, it features a spline profile matched to the mixer's input and may include a shear bolt collar or a flange connection depending on the mixer model. This yoke delivers the rotational power from the PTO shaft into the gearbox for speed reduction.
• Universal Joints (U-Joints)
  Two PTO shaft U-joint assemblies (also called cross and bearing kits) are installed at each end of the shaft. Each PTO shaft universal joint consists of a precision-ground cross with four needle-roller bearing caps. These joints allow the shaft to operate at an angle between the tractor and the mixer, accommodating changes in alignment as the equipment moves across uneven terrain.
• Inner Tube & Outer Tube
  The PTO shaft tube assembly consists of two telescoping sections: a lemon-profile inner tube that slides within a matching outer tube. Made from cold-drawn seamless steel, this PTO shaft tubing allows the shaft to extend and compress as the distance between the tractor and mixer changes. The precision profile ensures minimal play while maintaining smooth sliding action throughout the operating range.
• Slip Clutch Assembly
  The PTO shaft with slip clutch features a spring-loaded friction disc pack housed within a steel casing at the implement end of the shaft. When torque exceeds the calibrated threshold, the friction plates slip, decoupling the tractor side from the implement side. This protects the entire drivetrain from catastrophic damage caused by sudden overloads, foreign objects, or jammed auger blades.
• Safety Guard & Support Chains
  The PTO shaft guard is a two-piece plastic shield that encases the rotating shaft assembly to prevent operator entanglement. Easily removable for maintenance, the PTO shaft cover attaches to both end yokes via bearing-mounted collars and is held stationary by support chains. This guard system meets CE safety directives and is a mandatory component for safe PTO shaft operation in all agricultural environments.

PTO Tahrik Mili ile İlgili Yaygın Sorun Giderme Yöntemleri

1. Çalışma Sırasında Aşırı Titreşim
If the PTO shaft vibrates noticeably at operating speed, first check the universal joints for worn or seized needle bearings. A U-joint that does not pivot freely in all four directions needs immediate replacement. Next, verify that the operating angle between the tractor and the mixer does not exceed 15 degrees. An excessive angle causes the shaft to oscillate unevenly with each rotation, generating vibration that worsens at higher RPM. Also confirm the inner and outer tubes are not bent or dented, as physical damage to the PTO shaft tube disrupts rotational balance.

2. Kaymalı kavrama çok sık devreye giriyor.
If the slip clutch slips during normal mixing without an obvious blockage, the friction discs may be worn or the clamping springs may have weakened. Inspect the clutch plates for glazing, excessive wear, or oil contamination. Replace worn plates as a set. If the plates appear serviceable, increase the preload on the clutch springs slightly by tightening the adjusting nuts evenly. However, do not overtighten, as this can defeat the overload protection and transfer shock loads directly into the gearbox.

3. Mil Düzgün Bir Şekilde Uzayıp Kısalmayacak
Difficulty extending or compressing the PTO shaft tube usually results from inadequate lubrication, corrosion, or accumulated debris on the sliding surfaces. Separate the inner and outer tubes, clean both profiles with a wire brush, and apply a liberal coat of anti-seize grease to the mating surfaces. Reassemble and cycle the tube several times by hand to verify smooth action. In severe cases, corrosion pitting on the tube surfaces may require replacing the PTO shaft tubing entirely.

4. Emniyet cıvatası tekrar tekrar kırılıyor.
Repeated shear pin PTO shaft failures indicate either a recurring overload condition or the use of incorrect bolt grade. Verify you are installing the exact shear bolt grade specified by the manufacturer. Never upgrade to a higher-strength bolt, as this transfers the overload force into more expensive drivetrain components. If the correct bolt continues to fail, inspect the mixer auger for obstructions, worn knives, or bearing seizure that may be causing abnormally high resistance during mixing.

5. Üniversal Mafsallardan Gelen Olağandışı Ses
Clicking, clunking, or grinding sounds from the PTO shaft U-joint area indicate bearing wear or insufficient lubrication. Service the grease fittings on each U-joint with a lithium-based EP grease gun. If noise persists after greasing, the needle bearings inside the cross caps are likely worn beyond service limits. Replace both universal joints as a set to maintain balanced operation. Always confirm that replacement cross-and-bearing kits match the original PTO shaft sizes (27 x 74.6 mm for this assembly).

Feed Mixer PTO Shaft & Feed Mixer Gearbox

The feed mixer PTO shaft is the mechanical link that carries rotational energy from the tractor's Power Take-Off output to the feed mixer. Built from high-strength alloy steel, it consists of telescoping tubes, forged yokes, and precision universal joints that maintain smooth power delivery even as the tractor and mixer move over uneven terrain. For Jaylor single auger TMR mixers, this PTO drive shaft operates at a standardized 540 RPM and incorporates either a slip clutch or a shear bolt overload protection system to guard against drivetrain damage. Without a properly functioning PTO shaft, the mixer's internal components cannot receive the rotational power they need to operate.

The feed mixer gearbox, typically a planetary gearbox in vertical TMR mixers like the Jaylor 6350, 6400, 6425, and 6575, sits at the top of the mixing chamber. It receives the 540 RPM rotational input from the PTO shaft and reduces it to approximately 41 RPM at the auger output while multiplying torque dramatically. This speed reduction is essential because the heavy, dense feed material inside the mixer requires extremely high torque at low speed to be processed effectively. The planetary gearbox design distributes the load across multiple planet gears, resulting in a compact, efficient, and durable unit that can handle the sustained torque demands of daily mixing operations.

These two components form an inseparable power transmission chain. The PTO shaft is the delivery mechanism, and the gearbox is the conversion mechanism. The shaft's implement-end yoke connects directly to the gearbox's input shaft via a splined coupling, creating a rigid rotational link. When the tractor engages its PTO, power flows from the engine through the tractor's internal PTO gearing, out through the stub shaft, along the PTO driveline shaft through its U-joints and telescoping tubes, through the slip clutch, and into the planetary gearbox. The gearbox then converts the incoming high-speed, lower-torque rotation into the low-speed, high-torque output needed to drive the auger. If either component fails or is mismatched, the entire feed mixing process stops. Selecting a PTO shaft and gearbox that are rated for compatible torque, speed, and spline specifications is critical for long service life and reliable daily performance. CMN Transmission supplies both feed mixer PTO shafts and feed mixer gearbox units, ensuring perfect compatibility and single-source convenience for your Jaylor mixer drivetrain needs.

CMN Transmission'ın Tarımsal PTO Şaftlarını Neden Tercih Etmelisiniz?

CMN Transmission is one of the world's leading suppliers of industrial power transmission system solutions, producing a comprehensive range of products including agricultural gearboxes, PTO drive shafts, planetary gearboxes, hydraulic cylinders, chain sprockets, bevel gears, and couplings. As a family-owned company, our strength lies in combining traditional values with a young, dynamic team that drives the company to remain agile and innovative in the global marketplace. Our business purpose is "Transmit Force, Drive Future," and we fulfill that mission every day by engineering PTO shafts and drivetrain components that farmers and operators across six continents rely on for their critical daily operations.

When you select a PTO shaft from CMN Transmission, you connect directly with the manufacturer instead of navigating multiple distributor layers that add unnecessary cost. Our main production base works alongside more than ten shareholding cooperative factories, giving us complete oversight of raw material selection, CNC machining tolerances, heat treatment processes, and final assembly quality inspection. This direct integration means any technical question reaches our engineering staff immediately rather than a distant call center. The result is factory-direct pricing that typically runs significantly lower than what regional distributors charge for identical specifications, often delivering substantial savings while maintaining the same or better quality than premium European brands.

Every agricultural PTO shaft produced at CMN Transmission follows a documented ISO 9001 quality management system and complies fully with CE machinery safety requirements. We also hold TS16949 automotive quality certification, which imposes even stricter process controls on our forging, machining, and assembly operations. Our PTO drive shafts are precision engineered to serve as direct replacements for leading industry brands including Bondioli & Pavesi, Weasler, and Walterscheid, matching original specifications in spline profile, tube diameter, cross-and-bearing dimensions, and protective guard design so operators can swap components without modification or downtime.

With products exported to over 53 countries spanning Europe, North America, South America, the Middle East, Africa, Southeast Asia, and Oceania, CMN Transmission has an in-depth understanding of diverse agricultural markets and the specific requirements of each region. Whether you need a standard catalog 540 PTO shaft, a custom PTO shaft built to your unique specifications, or a complete OEM drivetrain package including PTO shafts and gearboxes, our team is ready to deliver with fast lead times of 7 to 15 days. We support full customization including custom PTO shaft lengths, non-standard spline profiles, specialized coatings, and private label branding. Contact us today to request a quotation and experience why thousands of agricultural operations worldwide trust CMN Transmission for their tractor PTO shaft needs.

SSS

Q: What PTO shaft size do I need for a Jaylor 6425 single auger TMR mixer?
A: The Jaylor 6425 single auger TMR mixer requires a Category 4 (Size 6) PTO shaft rated for 540 RPM operation. The tractor-end yoke should match your tractor's PTO stub spline, which is most commonly a 1 3/8" - 6 spline configuration. CMN Transmission supplies this exact PTO shaft size pre-configured for all Jaylor 6000 series single auger models. Contact us with your tractor make and model if you need to verify spline compatibility before ordering.

Q: Can I use a 1000 RPM PTO shaft on a Jaylor 6350, 6400, 6425, or 6575 mixer?
A: No. The Jaylor 6350, 6400, 6425, and 6575 single auger TMR mixers are designed to operate at 540 RPM. Installing a 1000 PTO shaft would deliver nearly double the intended rotational speed to the planetary gearbox, causing severe damage to the gearbox, auger assembly, and potentially the tractor PTO itself. Always verify that the PTO speed matches the mixer specification before connecting any PTO drive shaft.

Q: Is this PTO shaft a direct replacement for Bondioli and Pavesi PTO shafts?
A: Yes. This CMN Transmission PTO drive shaft is precision engineered as a direct replacement of Bondioli & Pavesi PTO shaft assemblies. It matches the original equipment's spline profile, tube diameter, cross-and-bearing dimensions, and protective guard design. Operators can install this replacement PTO shaft without any modifications, shimming, or additional adapters. It also serves as a compatible replacement for Walterscheid and Weasler PTO shaft units used on Jaylor mixers.

S: Yem karıştırıcım için kaymalı kavramalı PTO mili mi yoksa emniyet cıvatalı PTO mili mi seçmeliyim?
A: For feed mixer applications, a PTO shaft with slip clutch is generally the preferred choice because feed mixers encounter frequent, moderate overload events such as processing frozen silage or tangled bale twine. The slip clutch resets automatically without requiring any replacement parts. A shear bolt PTO shaft is an economical alternative suitable for operations where overloads are infrequent, but each overload event requires stopping to install a new shear bolt before resuming mixing.

Q: What is the correct PTO shaft length for Jaylor 6000 series single auger mixers?
A: The standard PTO shaft length for Jaylor 6350, 6400, 6425, and 6575 mixers features a closed length of approximately 850 mm and a maximum extended length of approximately 1,200 mm. However, actual requirements depend on your specific tractor's hitch dimensions and PTO stub shaft position. CMN Transmission offers custom PTO shaft lengths and can manufacture shafts to your exact measurements if the standard PTO shaft dimensions do not match your setup.

Q: How often should I grease the PTO shaft universal joints on my feed mixer?
A: Grease the PTO shaft U-joints every 8 to 10 hours of operation, or at minimum once per week during active feeding season. Use a quality lithium-based EP grease applied through the grease fittings on each U-joint cross until fresh grease appears at all four bearing caps. Regular greasing is the single most important maintenance step to extend the service life of your agricultural PTO shaft and prevent premature bearing failure on your Jaylor mixer driveline.

Q: What is the maximum operating angle for this tractor PTO shaft?
A: The maximum recommended operating angle for this standard PTO driveline shaft is 15 degrees. Exceeding this angle accelerates PTO shaft universal joint wear exponentially, leading to vibration, noise, and premature bearing failure. If your tractor and mixer setup requires a greater articulation angle, CMN Transmission offers a constant velocity (CV) PTO shaft option that supports operating angles up to 25 degrees while maintaining smooth, vibration-free power delivery.

Q: Can CMN Transmission build a custom PTO shaft for non-standard tractor configurations?
A: Yes. CMN Transmission specializes in custom PTO shaft manufacturing for non-standard applications. If your tractor uses an uncommon spline profile, requires a non-standard PTO shaft length, or needs a specific PTO shaft adapter to bridge incompatible connections, our engineering team can design and manufacture a shaft to your exact specifications. Provide your tractor PTO stub spline dimensions, required shaft length range, and mixer model, and we will supply a fully matched custom PTO shaft assembly.

Q: Do you ship PTO drive shafts internationally for Jaylor feed mixer replacements?
A: Yes. CMN Transmission exports tractor PTO shafts and PTO shaft parts to over 53 countries across six continents, including North America, Europe, South America, Australia, Africa, and Asia. We offer multiple shipping options including sea freight for cost efficiency and air freight for urgent orders. Every PTO drive shaft leaves our factory with a protective sleeve coating on the slip profile and pre-greased universal joints, ready for immediate installation upon arrival at your farm.

Q: What minimum tractor horsepower do I need to run a Jaylor 6575 with this PTO shaft?
A: The Jaylor 6575 single auger TMR mixer requires a minimum of 90 PTO horsepower from the tractor. This PTO shaft is rated for Category 4 service loads and is designed to handle the full torque output of tractors in this horsepower range at 540 RPM. For the smaller models, minimum PTO horsepower requirements are approximately 50 HP for the 6350, 60 HP for the 6400, and 70 HP for the 6425. Always ensure your tractor meets the minimum specification to prevent overloading the PTO shaft and drivetrain.

Q: Where can I buy replacement PTO shaft parts like U-joints, yokes, and shear bolts?
A: CMN Transmission supplies individual PTO shaft parts including replacement PTO shaft U-joints (cross and bearing kits), PTO shaft yokes (both tractor-end and implement-end), PTO shaft shear bolts, slip clutch friction disc kits, PTO shaft tubes (inner and outer), and PTO shaft guard assemblies. All parts are dimensionally matched to this specific Jaylor feed mixer PTO shaft assembly. You can order replacement parts directly through our website at korea-transmission.com or by contacting our sales team for part numbers and pricing.

Müşteri Yorumları

David Kowalski, Dairy Farm Owner, United States
"We run a 220-cow dairy in Wisconsin and our Jaylor 6425 mixer goes out twice a day, 365 days a year. The original PTO shaft finally gave out after about five seasons, the U-joints were completely shot. Ordered the CAT4 replacement from CMN Transmission and it arrived in just under two weeks. The spline fit was exact on our 1 3/8" - 6 tractor stub, no adapters needed. We are now about 250 hours in on the new shaft and the slip clutch has saved us twice when bale twine jammed the auger. Very satisfied with the build quality. The safety guard feels much sturdier than the OEM one we had before."

Tyler Morrison, Ranch Manager, Canada 
"I manage a beef backgrounding operation in Alberta, running around 600 head through winter. We use a Jaylor 6575 and push it pretty hard, three mixes a day with heavy barley silage and straw. Had a Walterscheid shaft on it before that kept eating U-joints every second season. Switched to CMN Transmission this year and the difference in the universal joint quality is noticeable. The bearings feel smoother and the grease fittings are actually accessible unlike the old ones. Price was significantly less than what our local dealer quoted for a Walterscheid replacement. Good value."

Craig Henderson, Station Manager, Australia
"We purchased two PTO shafts from CMN for our Jaylor 6400 and 6425 mixers on our cattle station in Queensland. Shipping to Australia took about three weeks door to door, which was faster than I expected given the distance. The packaging was solid, double boxed with foam around the yoke ends so nothing got dinged during transit. Both shafts installed without issues and have been running daily for about four months now. The telescoping tube action is smooth and the guards fit well. We will be ordering spare cross and bearing kits for preventive maintenance next season."

Klaus Bergmann, Farm Director, Germany
"Wir betreiben einen Milchviehbetrieb mit 180 Kuehen und nutzen einen Jaylor 6425 Futtermischer. [Translation:] We operate a dairy with 180 cows and use a Jaylor 6425 feed mixer. The previous PTO shaft developed serious play in the tube profile after three years. Contacted CMN through their website, and their technical team responded within 24 hours with the exact part number and dimensions. The shaft arrived at our farm near Hamburg in 12 days. Installation took about 30 minutes. The quality of the forged yokes and the overall PTO shaft length matched the original perfectly. Their customer service was responsive and professional. Very good experience from start to finish."

Hamish O'Neill, Sheep Farmer, New Zealand
"I run a 400-ewe sheep enterprise in Canterbury, New Zealand, and we use a Jaylor 6350 to mix lucerne baleage with grain and minerals. The old PTO shaft stripped out its shear bolt collar threads, so I needed a full replacement. Went with CMN because their price point was hard to beat and they had the right spec in stock. The shaft arrived well packed and fit straight onto our tractor's 540 PTO stub. We have been through about two months of daily mixing and it runs smooth, no vibration. For the price, the quality is excellent. Only minor point is I wish the installation guide had been included in the box rather than just online."

Roberto Salazar, Rancher, Mexico
"We are a cattle operation in Chihuahua, Mexico. We needed a replacement PTO drive shaft for our Jaylor 6400 mixer urgently because the old one failed mid-season during our busiest feeding period. CMN Transmission expedited the order and it arrived in 10 days. The shaft quality is comparable to the Bondioli and Pavesi unit we replaced, maybe even better in the guard quality. The slip clutch engaged once when we hit a frozen block of silage and it protected the gearbox exactly as it should have. Good product, fast delivery when we needed it most."

Marcelo Ferreira, Cooperative Manager, Brazil
"Our cooperative runs four Jaylor mixers across different sites in Minas Gerais. We had been buying European-brand PTO shafts through a distributor in Sao Paulo but the lead times were getting longer and the prices kept climbing. A colleague recommended CMN Transmission. We ordered a batch of four 540 RPM PTO shafts and they arrived in good condition after about 18 days. All four installed without modifications and have been running for about six months now. The cost savings across four units was substantial. We have already placed a second order for spare PTO shaft parts including U-joints and shear bolts."

Sean Callahan, Dairy Farmer, Ireland
"We have a 300-head dairy near Galway and use a Jaylor 6425 for TMR mixing. The previous PTO shaft was a generic aftermarket unit that lasted barely two seasons before the tube profile wore out and developed excessive slop. Ordered from CMN based on a recommendation from another Irish farmer. The shaft arrived in about two weeks and the fit was right on the money. What impressed me most was the anti-corrosion coating on the tubes. Ireland is wet, and corrosion kills PTO shafts here faster than wear does. After eight months of daily use in our climate, the tubes still slide smoothly with no signs of rust. Well built."

Johan van der Merwe, Feedlot Manager, South Africa
"We operate a large-scale feedlot near Johannesburg using Jaylor 6575 mixers for approximately 1,200 head. Replacement PTO shafts from the original equipment dealers here in South Africa are very expensive and take weeks to arrive. Found CMN Transmission online and decided to trial one unit. The 540 PTO shaft arrived well packaged in 14 days. The forged yokes, the universal joint quality, and the overall build are clearly a step above some of the cheaper alternatives we tested before. We have been running it for five months now with zero issues. Already ordered two more for our other mixers. The factory direct pricing makes a real difference for our operating budget."