Select Page

CMN-30 Flail Mower Gearbox Ratio 1:2.9 30 HP 540 RPM Right Angle PTO Gearbox

The CMN-30 is a right angle PTO gearbox built for compact and medium-duty flail mowers that run off a standard 540 RPM tractor power take-off. With a 1:2.9 speed-increasing ratio and a 30 HP power rating, this flail mower gearbox converts the relatively slow PTO rotation into faster drum speed, delivering the torque required to shred grass, brush, and crop residue with consistent results. Its nodular cast iron housing absorbs vibration, resists impact loads, and shields the internal bevel gears and bearings from dust, plant debris, and moisture.

The CMN-30 is a right angle PTO gearbox built for compact and medium-duty flail mowers that run off a standard 540 RPM tractor power take-off. With a 1:2.9 speed-increasing ratio and a 30 HP power rating, this flail mower gearbox converts the relatively slow PTO rotation into faster drum speed, delivering the torque required to shred grass, brush, and crop residue with consistent results. Its nodular cast iron housing absorbs vibration, resists impact loads, and shields the internal bevel gears and bearings from dust, plant debris, and moisture. At just 13.5 kg, the unit keeps total mower weight low without sacrificing structural rigidity, making it a practical choice for 3 point flail mower setups on sub-compact and utility tractors.

Whether you manage pasture, maintain roadsides, or clear vineyard under-rows, this agricultural flail mower gearbox pairs a compact footprint with the mechanical endurance that field work demands. The 1 3/8" Z6 splined input accepts common PTO shaft connections, while the optic-axis output accommodates a range of drum and knife mounting configurations. Each unit leaves the factory filled with the recommended flail mower gearbox oil, sealed with reinforced oil seals, and backed by CE and ISO 9001 certification. For operators who need a proven tractor flail mower gearbox that bolts in place of worn or damaged originals, the CMN-30 delivers dependable daily performance across seasons of heavy use.

CMN-30 Flail Mower Gearbox

Technical Parameters

ModelCMN-30
Ratio1:2.9
Teeth32/11
Module3.0
Power (HP)30 HP
Rated Input540 rpm
Input/Output Description1 3/8 Z6 / Optic axis
Weight (Kg)13.5 Kg

We have completed a third-party supplier audit and company verification supported by SGS / TÜV Rheinland. This verification helps buyers review company identity, business operations, supplier profile and general manufacturing capability. Product-specific inspection reports, material documents or compliance records can be provided according to order requirements.

Minimum Order Quantity (MOQ): Flexibly set based on the product type and order amount.

Samples: New customers may request 1–5 samples under appropriate circumstances.

Mixed Orders: Combining different models is supported; the total order amount must reach approximately $1,500.

Small Orders: Orders starting from 1–2 pieces are supported, but the unit price will be relatively higher.

Lead Time: 10–25 working days for standard parts; 20–45 working days for customized components; 45–120 working days for project-based equipment.

Trade Terms: EXW, FOB, CIF, and DAP are generally supported; FCA, CFR, CPT, CIP, and DDP terms can be specifically negotiated.

CMN-30 Flail Mower Gearbox Dimensions

CMN-30 Flail Mower Gearbox Dimensions

Key Features of the CMN-30 Flail Mower Gearbox

1. Power Transmission and Speed Conversion
This 540 RPM flail mower gearbox accepts the standard tractor PTO input and multiplies rotational speed through a 1:2.9 bevel gear set, producing roughly 1,566 RPM at the output shaft. The increased drum speed, combined with higher torque, keeps the flail rotor chopping at a steady rate even when grass density or stalk thickness changes mid-pass. That consistent rotor speed is what separates a clean cut from a ragged one across variable field conditions.

2. Durability and Housing Protection
The heavy duty flail mower gearbox housing is cast from nodular iron and finished with a corrosion-resistant coating that stands up to constant exposure to grass sap, soil particles, and wet field conditions. Internal gears and bearings sit behind reinforced lip seals that block dirt, plant debris, and moisture from reaching the gear mesh. This sealed construction greatly reduces wear on the flail mower gearbox bearings and extends maintenance intervals by keeping contaminants out of the lubricant.

3. Ratio Options and Modular Output
The 1:2.9 flail mower gearbox ratio of the CMN-30 is calibrated for compact and mid-range flail drums, delivering the rotor speed most commonly specified by European and North American mower manufacturers. The optic-axis output shaft design accepts different drum adapters, knife holders, and coupling flanges, so a single gearbox model can serve various flail assemblies. That modularity lowers spare-parts inventory for dealers and simplifies the flail mower gearbox replacement process for end users in the field.

4. Sealing and Corrosion Resistance
Every flail mower gearbox oil seal on the CMN-30 is made from FKM-grade rubber that resists heat, fuel splashes, and agricultural chemicals. The double-lip seal profile retains lubricant pressure inside the housing and prevents fine particulates from migrating inward along the shaft surfaces. Combined with the coated housing exterior, these sealing measures let the gearbox operate reliably in coastal salt air, humid tropical climates, and the abrasive dust conditions common in dry-season stubble work without accelerated corrosion.

5. Safety and Overload Protection
Flail mowers frequently strike hidden rocks, wire, or root stumps that can send extreme shock loads through the driveline. The CMN-30 is designed to work alongside slip clutches, shear bolts, or torque-limiting devices installed in the PTO shaft assembly. These protection mechanisms interrupt torque transmission before the spike reaches the gears, preventing cracked teeth or bent shafts. This layered approach to overload protection keeps the gearbox safe and avoids the downtime and cost of an emergency flail mower gearbox repair.

6. Compact and Lightweight Construction
Weighing only 13.5 kg, the CMN-30 is one of the lightest units in its power class. The compact envelope fits into tight mower frames where space between the PTO connection and the rotor drum is limited. This lightweight build reduces the total implement weight hanging off the tractor's three-point hitch, which helps smaller tractors maintain stability on hillsides and uneven terrain. Despite the reduced mass, the nodular iron housing retains the wall thickness needed for long service life under daily workloads.

Flail Mower Gearbox

Operating Principle

Flail mower gearboxes sit at the heart of every flail cutting system, linking the tractor's power take-off to the spinning rotor that carries dozens of individual flail blades. The CMN-30 performs this connection through a pair of hardened spiral bevel gears arranged at a 90-degree angle inside a sealed, oil-filled housing. When the operator engages the PTO, rotation travels from the tractor through the driveline shaft into the gearbox input, which is a 1 3/8" Z6 splined shaft spinning at the standard 540 RPM. The 11-tooth input pinion meshes with the 32-tooth ring gear, and because the smaller gear drives the larger one, the output shaft spins faster rather than slower. That 1:2.9 multiplication produces an output speed of approximately 1,566 RPM, which is the range most flail drum manufacturers specify for clean, fine mulching of grass, weeds, and crop residue.

The right-angle layout of this flail mower PTO gearbox redirects the horizontal PTO rotation by 90 degrees to the vertical (or angled) axis that the drum requires. This change in direction is handled entirely by the spiral bevel gear geometry, which also distributes tooth contact across a wider area than straight-cut bevel gears. The result is quieter running, lower vibration, and more even load sharing across the gear face, all of which reduce internal heat and extend gear life.

Inside the housing, two sets of tapered roller bearings support the input and output shafts. These bearings handle both radial and axial loads, keeping the gear mesh alignment within tight tolerances even under the sudden shock loads that occur when flails hit concealed obstacles. The oil bath lubrication system continuously coats the gear teeth and bearing races, carrying away heat generated by friction. Proper flail mower gearbox oil level is critical: too little oil starves the upper bearings during operation, while overfilling raises churning losses and operating temperature.

The output shaft exits the housing through a reinforced oil seal and connects to the flail drum via a flange, coupler, or keyed adapter, depending on the mower design. As the drum spins, the centrifugal force swings the flails outward, and each blade tip strikes vegetation at high speed, cutting and shredding the material into small pieces that decompose quickly on the soil surface. Because the gearbox maintains a stable output speed regardless of minor fluctuations in engine RPM, the cutting quality stays consistent from one end of the field to the other.

Flail Mower Gearbox

Applications of the CMN-30 Flail Mower Gearbox

Vegetation Shredding and Pasture Maintenance

The CMN-30 powers the flail drum to cut and mulch grass, weeds, and crop residues across grazing land and hay fields. Its 1:2.9 ratio keeps blade-tip speed high enough for a fine mulch that breaks down quickly, returning nutrients to the soil and promoting even regrowth across the pasture for the next grazing cycle.

Brush and Bramble Control

When thick brambles, blackberry canes, or small woody stems build up along fence lines and field margins, this heavy duty flail mower gearbox provides the torque needed to shred them without stalling. The robust bevel gear set absorbs the extra resistance these tougher materials create, keeping the drum turning at a productive rate while the tractor operates at a moderate PTO load.

Vineyard and Orchard Under-Row Work

Compact flail mowers fitted with offset arms reach beneath vine rows and between tree trunks where rotary cutters cannot go. The CMN-30's small footprint and light 13.5 kg weight make it well suited for these narrow-row machines, keeping overall implement width minimal while still delivering the drum speed needed for a clean pass between vines and low-hanging branches.

Roadside and Municipal Mowing

Highway departments and municipal crews rely on flail mowers for verge maintenance because flails throw less debris than rotary decks. The CMN-30's sealed housing and coated exterior handle the daily exposure to road grime, salt spray, and gravel impacts that come with this type of work, while the reinforced oil seal prevents leaks during long hours of continuous roadside operation.

Crop Residue Management

After harvest, standing stubble and leftover stalks need to be chopped down before the next tillage pass. This agricultural flail mower gearbox drives the rotor at a speed that pulverizes corn stalks, cereal residue, and cover crop biomass into short fragments, speeding decomposition and making the field easier to till. The fine mulch left behind also helps suppress weed germination between planting cycles.

Sports Turf and Amenity Grass Care

Golf course roughs, parkland, and sports-field perimeters often use flail mowers for a clean, even finish without the scalping risk of rotary decks. The CMN-30's consistent output speed helps maintain an even cut height across undulating terrain, and its compact size suits the smaller PTO-driven mowers used in amenity and landscape maintenance settings where a tidy appearance is expected.

Solar Farm and Utility Site Vegetation Control

Solar panel arrays, electrical substations, and pipeline corridors require regular vegetation management to prevent fire hazards and maintain access. Flail mowers powered by a gearbox like the CMN-30 mulch growth in place rather than throwing clippings onto sensitive equipment. The low-debris discharge of a flail system, combined with the gearbox's sealed design, makes it a practical choice for these controlled environments.

Slope and Embankment Mowing

Hydraulic-arm flail mowers that reach down embankments and ditch banks rely on lightweight gearboxes to keep the boom balanced. The CMN-30's 13.5 kg weight reduces the moment load on the hydraulic arm, allowing the operator to reach steeper angles without exceeding the arm's rated capacity. Its sealed housing also protects internals from the mud and standing water often found at the base of drainage ditches.

Flail Mower Gearbox Applications

CMN-30 Flail Mower Gearbox Manufacturing Process

Step 1: Raw Material Selection and Inspection
Every production run starts with incoming material inspection. The nodular cast iron for the housing and the alloy steel bar stock for shafts and gears are tested for chemical composition and mechanical properties before being released to the shop floor. Samples from each heat are checked for hardness, grain structure, and inclusion levels, ensuring that only material meeting the required metallurgical standards enters the machining process.

Step 2: Housing Casting and Machining
The gearbox housing is poured in precision sand molds, then cleaned, shot-blasted, and X-ray inspected for porosity or voids. Once cleared, the castings move to CNC machining centers where bearing bores, shaft passages, and mating surfaces are machined to tight tolerances. The mounting flange face is finished in a single clamping to guarantee flatness and perpendicularity relative to the shaft centerlines.

Step 3: Gear Cutting and Tooth Profiling
The 11-tooth pinion and 32-tooth ring gear are rough-cut on Gleason-type bevel gear generators, then finish-lapped as a matched pair. Lapping the gears together produces a contact pattern that covers 60 to 70 percent of the tooth face, distributing load evenly and reducing noise. Each matched set is marked with a serial number so the two gears stay together throughout assembly and any future flail mower gearbox parts orders.

Step 4: Heat Treatment
Gears and shafts undergo carburizing in a controlled-atmosphere furnace, then oil quenching and tempering. This process creates a hard, wear-resistant case on the tooth surfaces and shaft journals while keeping the core ductile enough to handle impact loads. Hardness is verified on every batch with Rockwell testing, and case depth is checked with cross-section micro-hardness measurements to confirm that the heat-treatment cycle reached the specified profile.

Step 5: Shaft Machining and Spline Grinding
Input and output shafts are turned on CNC lathes, and the 1 3/8" Z6 splines on the input shaft are hobbed, then ground to the final profile. Bearing journals are finish-ground to Ra 0.4 or better so the tapered roller bearings seat without micro-fretting. The seal contact bands are polished to an even finer finish, extending the working life of the oil seals and reducing the chance of early leaks during the first hours of field operation.

Step 6: Assembly and Bearing Preload Adjustment
Skilled technicians press bearings onto shafts, install matched gear sets, and shim the bearing preload to the specified value. Correct preload is critical: too loose and the gears vibrate under load; too tight and the bearings overheat. After shimming, each assembly is rotated by hand to check for smooth, drag-free movement. Seals are then pressed into position, and the housing halves are bolted together with controlled torque sequences.

Step 7: Run-In Testing and Quality Inspection
Every finished gearbox is filled with the factory-specified gear oil and mounted on a test bench that simulates PTO input at 540 RPM. The unit runs under load for a set break-in period while technicians monitor noise level, vibration amplitude, oil temperature, and seal integrity. Units that exceed any threshold are pulled for rework. Passing units receive a dated inspection stamp and are cleared for surface coating and final packing.

Step 8: Surface Coating and Packaging
After testing, the housing exterior is coated with an anti-corrosion primer and topcoat that protects the iron surface during shipping and storage. Output and input shaft splines are coated with rust-preventive grease, and exposed machined surfaces are sealed with VCI (volatile corrosion inhibitor) film. Each unit is boxed with mounting hardware, an oil-level instruction card, and a certificate of conformance before it ships from the factory.

Flail Mower Gearbox

How to Choose the Right Gearbox for a Flail Mower

1. Identify Your Machine First
Before opening any catalog, write down the mower brand, model number, cutting width, and the type of vegetation you cut most often. Take photos of the existing gearbox: one mounted, one removed, and close-ups of the input and output shaft interfaces plus the nameplate. Measure the mounting hole spacing and shaft diameters with a ruler or caliper. This documentation prevents the "almost fits" problem that leads to returns and wasted downtime.

2. Match Power Rating to Your Hardest Work
A gearbox rated at exactly your tractor's PTO horsepower works fine on flat pasture under light load. But if you regularly cut heavy brush, orchard prunings, or uneven ground with hidden obstacles, shock loads can exceed the steady-state rating. Size the gearbox for the toughest conditions you face, not the average ones. The small cost difference between a unit that fits tight and one that has margin is nothing compared to an in-season failure.

3. Verify Gear Ratio and Rotation Direction
The flail mower gearbox ratio determines drum speed from your PTO input. The CMN-30's 1:2.9 ratio at 540 RPM yields about 1,566 RPM output. But ratio alone is not enough: confirm the output rotation direction matches what your mower's drum needs. Different brands and mounting positions can require opposite rotations. A gearbox that fits the flange but spins the wrong way will not cut properly and can damage the blade holders.

4. Check Shaft Interface Compatibility
The input shaft must accept your PTO driveline yoke, and the output shaft must fit your drum coupler or adapter. For a 540 RPM setup, the standard is a 1 3/8" Z6 splined input. The output can vary: optic axis, keyed shaft, or splined, depending on the mower manufacturer. Check both ends carefully, counting spline teeth and measuring shaft diameters, before placing an order for any flail mower gearbox replacement.

5. Confirm Overload Protection Setup
No gearbox, however strong, is guaranteed to survive a full jam without overload protection in the driveline. Decide whether your operation is better served by a shear-bolt setup (simple, cheap, requires a stop to replace) or a slip clutch (slips repeatedly, needs annual inspection). Never upgrade the shear bolt to a higher grade on your own: doing so defeats the intended protection and shifts the failure point to the gearbox internals.

6. Evaluate Mounting Dimensions
Bolt-hole patterns, flange thickness, and housing height all need to match the mower frame. Even a few millimeters of misalignment in the mounting holes can require adapter plates, re-drilling, or shimming that introduces vibration and shortens bearing life. The CMN-30 uses a common European and North American bolt pattern, but always verify by laying out the new gearbox against the frame or old unit before final tightening.

7. Consider Lubrication and Cooling
Use the fill plug to add the manufacturer-recommended gear oil grade and check the level before every use. Overfilling raises churning losses and operating temperature, while under-filling starves the upper bearings. If your workload involves long hours in hot weather or heavy brush cutting, ask about the housing's heat-dissipation characteristics. A gearbox with more external ribbing or a larger housing surface area will run cooler under sustained high loads.

Flail Mower Gearbox

Flail Mower Gearboxes and Agricultural PTO Shafts

A flail mower gearbox and a PTO drive shaft work as a matched pair. Neither component can function in isolation: the driveline shaft carries rotational power from the tractor's PTO stub to the gearbox input, and the gearbox converts that power into the speed and direction the flail drum requires. An agricultural PTO shaft for a flail mower is a telescopic mechanical link that transfers rotational power from the tractor's power take-off stub to the mower's gearbox input. It typically consists of two tubular halves connected by a slip joint that allows the shaft to extend and compress as the three-point hitch raises and lowers the implement. At each end, a universal joint (U-joint) accommodates the angular misalignment between the tractor PTO stub and the gearbox input shaft. Protective guards enclose the spinning shaft and U-joints to prevent contact with clothing or limbs. The tractor-side yoke uses a splined bore that matches the tractor PTO profile (1 3/8" Z6 for 540 RPM applications), while the implement-side yoke connects to the gearbox input spline.

When the operator engages the PTO, rotation travels from the tractor stub through the driveline shaft's U-joints and telescopic tubes into the gearbox input shaft. The CMN-30 gearbox then multiplies that 540 RPM input to approximately 1,566 RPM at the output, redirecting the power 90 degrees to the vertical drum axis. The driveline shaft must be sized to handle the torque rating of the gearbox: a shaft rated below the gearbox's 30 HP capacity will fail at the U-joints or slip joint before the gearbox ever reaches its limit. Conversely, an oversized shaft adds unnecessary weight and cost.

Operating angle is another critical factor. PTO driveline shafts perform best when the U-joint angles at each end are equal and below 15 degrees. Exceeding that range creates cyclic speed fluctuations in the shaft, which transmit into the gearbox as pulsating loads that accelerate gear and bearing wear. Setting the tractor's three-point hitch to position the mower so both U-joints work at similar, moderate angles goes a long way toward extending the life of both the driveline and the flail mower gearbox.

Overload protection also sits in the driveline rather than inside the gearbox. A shear bolt or slip clutch integrated into the PTO shaft assembly acts as a sacrificial link: if the flail drum jams on a large rock or a buried cable, the protection device interrupts torque before the spike reaches the gearbox gears. Without this protection, a sudden jam can crack a tooth or bend a shaft, turning a simple obstacle strike into a full flail mower gearbox replacement job. Operators should always verify that the protection device on their driveline shaft is correctly specified for the gearbox's torque rating and inspect it at the start of each mowing season.

PTO Shaft

Flail Mower Gearbox vs. Fertilizer Spreader Gearbox

What Is a Flail Mower Gearbox?

A flail mower gearbox is a right-angle speed-increasing gear drive that transmits power from a tractor's PTO (commonly 540 RPM) to the flail rotor while maintaining consistent cutting performance. Its internal bevel or spiral bevel gear system regulates speed and torque to match different crop residues, grass heights, and terrain conditions. The heavy-duty housing construction ensures long-term reliability in the abrasive, high-vibration environment that flail mowing produces, making these gearboxes a cornerstone of modern vegetation management equipment.

Advantages of Flail Mower Gearbox

  • Speed Multiplication for Clean Cutting: The gear ratio increases PTO speed to the range needed for effective flail impact, producing a fine, even mulch rather than torn or ragged vegetation. This speed amplification is what gives flail mowers their superior finish compared to rotary alternatives.
  • Shock Load Tolerance: The bevel gear geometry and reinforced housing absorb sudden torque spikes from rocks, stumps, and wire entanglements without immediate gear failure. This built-in resilience reduces the frequency of unexpected breakdowns during daily cutting operations.
  • Sealed Against Debris: Reinforced double-lip seals and machined mating surfaces keep grass fibers, soil particles, and moisture out of the oil bath. This sealing extends oil change intervals and lowers the total cost of flail mower gearbox repair over the equipment's service life.
  • Compact Right-Angle Layout: The 90-degree power path fits within the narrow envelope of a flail mower frame, keeping the implement width manageable for three-point hitch mounting and field transport through gates and along narrow lanes.

Applications of Flail Mower Gearbox

  • Pasture and rangeland mowing, where operators need a clean cut without throwing stones or debris toward livestock fencing and structures.
  • Vineyard, orchard, and tree-nursery inter-row maintenance, where compact mower widths and low debris throw protect crops and irrigation lines.
  • Highway verge and municipal roadside maintenance, requiring durable gearboxes that withstand frequent contact with gravel and road debris.
  • Post-harvest crop residue shredding, speeding field decomposition and seedbed preparation ahead of the next planting cycle.

What Is a Fertilizer Spreader Gearbox?

A fertilizer spreader gearbox, also called a fertilizer distributor gearbox, is an essential component of agricultural spreading machinery. Positioned at the center of the implement, it transmits power from the tractor's PTO to spinning discs or augers that evenly distribute granular or powdered fertilizer across the field. These gearboxes are engineered for consistent output speed, adjustable spread patterns, and long-term reliability under the corrosive conditions that chemical fertilizers create. Their internal gear trains adjust rotational speed and torque based on spreading requirements, optimizing coverage uniformity and minimizing material waste.

Advantages of Fertilizer Spreader Gearbox

  • Precise Speed Regulation: The gear ratio is calibrated to maintain constant disc speed regardless of hopper load variation, ensuring uniform fertilizer distribution from a full load down to the last few kilograms in the hopper.
  • Chemical Corrosion Resistance: Housings are typically coated or made from corrosion-resistant alloys because fertilizer dust and granules are chemically aggressive. This protection prevents surface pitting and extends service life in continuous-use scenarios.
  • Multi-Output Capability: Many fertilizer spreader gearboxes feature twin output shafts that drive two spinning discs simultaneously, allowing wide spread widths in a single pass and reducing field traffic and soil compaction.
  • Low-Maintenance Design: Sealed bearings and lifetime-lubricated gear sets reduce the need for frequent oil changes in environments where downtime during the spreading season is costly.

Applications of Fertilizer Spreader Gearbox

  • Crop Farming: Uniform application of nitrogen, phosphorus, and potassium fertilizers across grain, vegetable, and fruit crops promotes optimal nutrient absorption and maximizes yield per hectare.
  • Pasture Management: In livestock farming, these gearboxes drive spreaders that distribute fertilizer evenly across grazing land, improving forage quality and carrying capacity.
  • Lawn and Turf Management: Sports fields, golf courses, and municipal parks use spreader gearboxes for precise, controllable fertilizer application that promotes healthy, even grass growth.
  • Horticulture and Nurseries: Greenhouses and nursery operations rely on precise fertilizer distribution for potted plants and ornamental crops, where over-application can damage sensitive root systems.
  • Landscaping and Gardening: Small-scale spreaders equipped with these gearboxes enable controlled fertilizer application in flower beds, residential lawns, and ornamental gardens.
  • Soil Amendments: Beyond fertilizer, these gearboxes also power spreaders that distribute lime, gypsum, comite, and compost, improving soil pH and organic content for better crop establishment.

Comparison Table

FeatureFlail Mower GearboxFertilizer Spreader Gearbox
Primary FunctionDrive flail rotor for vegetation cuttingDrive spinning discs or augers for fertilizer distribution
Gear Ratio DirectionSpeed-increasing (e.g., 1:2.9)Speed-reducing or 1:1
Typical Output Speed1,200 to 2,500 RPM300 to 900 RPM
Shock Load ExposureHigh (rocks, wire, stumps)Low (steady granular flow)
Corrosion Risk SourceMoisture, plant sap, soil abrasionChemical fertilizer dust and granules
Output Shaft CountSingle (one rotor)Single or dual (one or two discs)
Overload ProtectionSlip clutch or shear bolt (external)Rarely needed; low shock environment
Housing MaterialNodular cast iron or alloy steelCast iron or stainless-coated alloy
CMN-9.310 Flail Mower GearboxL-25J Fertilizer Spreader Gearbox 1-3

Why Choose CMN Transmission's Flail Mower Gearboxes?

Korea CMN Transmission Co., Ltd. was established in 2000 and is based in Sandan-o, Danwon-gu, Ansan-si, Gyeonggi-do, Korea. With over 100 factory employees dedicated to the research, development, manufacturing, sales, and service of agricultural gearboxes, CMN Transmission has spent more than two decades building a reputation as a reliable supplier in the global agricultural gearbox industry. Our products reach more than 60 destinations worldwide, and our annual production exceeds 500,000 units across nearly one thousand specifications.

Our product range covers rotary cutter gearboxes, rotary tiller gearboxes, feed mixer gearboxes, rotary mower gearboxes, fertilizer spreader gearboxes, flail mower gearboxes, post hole digger gearboxes, round baler gearboxes, square baler gearboxes, disc mower gearboxes, center pivot irrigation gearboxes, hydraulic drive gearboxes, silage machine gearboxes, orchard sprayer gearboxes, rotary rake gearboxes, combine harvester gearboxes, grain storage gearboxes, grain transportation gearboxes, corn header gearboxes, cutting bar gearboxes, poultry feeding gearboxes, and custom agricultural gearbox solutions. Beyond gearboxes, we also manufacture PTO shafts, U-joints, yokes, tubes, torque limiters, covers, adapters, couplings, bearings, blades, chains, and sprockets.

Every product leaves our facility under CE and ISO 9001 certified management systems, ensuring consistent quality and dependable performance from batch to batch. Our exports serve customers in the United States, Canada, Mexico, Brazil, Argentina, France, Germany, Italy, Spain, the United Kingdom, Russia, China, India, Thailand, Vietnam, Turkey, Australia, and New Zealand, backed by extensive experience providing technical solutions for agricultural machinery OEMs and distributors around the world.

What sets CMN Transmission apart is our willingness to work with customers at every stage. Need a direct replacement for a worn unit? We stock standard models like the CMN-30 for fast dispatch. Designing a new mower and need a gearbox tailored to your frame layout and rotor specs? Our engineering team accepts custom drawings and can produce prototypes on a timeline that keeps your development on schedule. We support custom production for agricultural gearboxes, PTO shafts, and various agricultural machinery components, all manufactured under the same quality controls as our standard catalog. When you choose CMN Transmission, you get a partner that combines factory-direct pricing with the technical depth of a dedicated agricultural gearbox manufacturer.

Rotary Tiller Gearbox Manufacturers

Frequently Asked Questions

Q: What oil should I use in my flail mower gearbox?
A: The CMN-30 is designed to run on EP-rated 80W-90 gear oil, which provides the film strength needed to protect hardened bevel gear tooth surfaces under high contact pressure. Fill the housing to the level plug and check before each use. Avoid overfilling, as excess oil causes churning that raises internal temperatures and reduces efficiency. Drain and replace the oil after the initial 50-hour break-in period, then at regular intervals of 200 to 300 operating hours or as specified by your mower manufacturer.

Q: How do I know when the flail mower gearbox oil seal needs replacing?
A: The most obvious sign is oil weeping or dripping around the input or output shaft. A thin film of oil is normal during the first few hours as the seal beds in, but a steady drip or visible oil trail on the housing surface means the seal has worn past its service limit. Other indicators include grit accumulation around the seal area, a noticeable drop in oil level between checks, or increased noise from the gearbox as contaminated oil loses its protective properties.

Q: Can I use the CMN-30 as a flail mower gearbox replacement on other brands?
A: Yes, the CMN-30 is built to common European dimensional standards and serves as a direct or near-direct replacement for many compact and medium-duty flail mowers from manufacturers like Comer, Bondioli, and similar OEM suppliers. The key compatibility factors are the mounting bolt pattern, the 1 3/8" Z6 input spline, the output shaft profile, and the 1:2.9 ratio. Confirm these dimensions against your original unit before ordering to ensure a proper fit without modification.

Q: What is the output speed of a 540 RPM flail mower gearbox with a 1:2.9 ratio?
A: With a 540 RPM PTO input and a 1:2.9 speed-increasing ratio, the output shaft of the CMN-30 spins at approximately 1,566 RPM. This output speed falls within the range most flail drum manufacturers recommend for effective vegetation mulching. The actual blade tip speed also depends on the drum diameter and flail arm length, so always cross-check the gearbox output speed with the drum manufacturer's recommended RPM range to avoid running outside the design window.

Q: How often should I inspect the flail mower gearbox bearings?
A: Check for bearing wear at the start of each mowing season and again at mid-season if you are running more than 300 hours annually. Warning signs include increased vibration, a growling or rumbling noise from the gearbox, and perceptible shaft play when you try to rock the input or output shaft by hand with the PTO disengaged. If you detect any of these symptoms, remove the gearbox for inspection before the bearing failure progresses to gear damage.

Q: Is the CMN-30 suitable for a 3 point flail mower on a sub-compact tractor?
A: Absolutely. At 13.5 kg and 30 HP rated capacity, the CMN-30 is a good match for sub-compact and utility tractors in the 20 to 30 HP range. Its lightweight construction keeps the total implement weight low, which helps smaller tractors maintain stability on hillsides and prevents the three-point hitch from being overloaded. Just make sure your tractor's PTO runs at the standard 540 RPM and the driveline shaft can handle the torque the gearbox will transmit.

Q: What causes a flail mower right angle gearbox to overheat?
A: The most common causes are low oil level, incorrect oil grade, overfilling, and sustained heavy-load operation in high ambient temperatures. A clogged breather vent can also raise internal pressure and temperature. If you notice the housing is too hot to hold your hand on after a work session, stop and check the oil level and condition. Discolored or burnt-smelling oil is a sign that the gearbox has been running above its design temperature and needs an oil change and potentially an inspection of the gears and bearings.

Q: Can I repair a flail mower gearbox myself, or should I send it to a shop?
A: Basic flail mower gearbox repair tasks like replacing seals and changing oil can be done in a farm workshop with standard tools. Bearing replacement and gear-set changes require more skill: you need to set bearing preload correctly with shims, and the matched gear pair must be installed as a set. If you are comfortable with bearing press work and have a torque wrench, a shop-level rebuild is feasible. Otherwise, CMN Transmission offers exchange programs where you send in the worn unit and receive a factory-rebuilt replacement.

Q: What is the difference between a flail mower gearbox and a rotary cutter gearbox?
A: A flail mower gearbox typically uses a speed-increasing ratio to spin the drum faster than the PTO input, while a rotary cutter gearbox usually has a 1:1 or speed-reducing ratio because rotary blades are larger and generate sufficient tip speed at lower RPM. Flail gearboxes also tend to be more compact and lighter, since flail mowers are smaller implements. The sealing requirements are similar, but flail mower gearboxes face more frequent shock loads because flail blades strike obstacles individually rather than as a single heavy blade.

Q: Does CMN Transmission offer custom flail mower gearbox assembly services?
A: Yes. CMN Transmission supports custom production based on customer drawings and specifications. If your mower frame requires a non-standard mounting pattern, a different output shaft configuration, or a modified gear ratio, our engineering team can work with you to produce a custom flail mower gearbox assembly that fits your exact requirements. Minimum order quantities apply for custom work, so contact our sales team early in your design process to discuss lead times and pricing for bespoke configurations.

Flail Mower Gearbox

Customer Reviews

Travis Mitchell, Cattle Ranch, United States
"We run a 400-acre beef operation in east Texas and needed a flail mower gearbox replacement for our compact Kuhn mower after the old one lost a bearing at the worst time. Ordered the CMN-30 as a direct swap. Bolt pattern lined up perfectly with no adapter plate, and the 1 3/8 Z6 spline matched our existing PTO shaft without modification. Put about 180 hours on it through summer and fall mowing. Oil came out clean at the first change, no metal particles at all. Very solid unit for the money."

Daniel Parsons, Hay and Pasture, Canada
"Bought two CMN-30 units for our contract mowing crew in southern Alberta. We cut ditches and pasture margins all season, so the gearboxes take a beating from rocks and fence wire. After a full season, neither unit needed any work beyond a standard oil change. Shipping from the factory to our shop in Lethbridge took about 11 days, which was faster than I expected for an international order. Customer support answered my pre-order questions about rotation direction within a day. Would order from CMN again."

Klaus Hartmann, Municipal Services, Germany
"Our municipality maintains about 60 km of roadside verges with offset-arm flail mowers. We switched to the CMN-30 after the previous brand kept leaking oil through the shaft seal after 300 hours or so. The CMN seal has held up well through a full mowing season, roughly 420 operating hours by the time we parked for winter. Build quality looks good, and the corrosion coating on the housing has not chipped despite constant contact with road gravel. Only reason for four stars instead of five is the instruction card could be more detailed on oil fill quantities."

Jean-Luc Moreau, Vineyard Management, France
"I manage 28 hectares of Cabernet vines in Bordeaux and use a narrow inter-row flail mower. The old gearbox was too heavy for the hydraulic arm, so I looked for something lighter. The CMN-30 at 13.5 kg solved the balance issue immediately. Installed it in March and ran it every two weeks through the growing season. The compact housing fits the mower frame with millimeters to spare, and the output adapter matched the drum coupler I already had. Quiet operation and no vibration. Exactly what a vineyard flail mower needs."

Marco Rinaldi, Olive Farm, Italy
"We needed a replacement gearbox for a 1.2-meter flail mower that runs between our olive rows in Puglia. The CMN-30 was recommended by a dealer in Bari who had stocked CMN parts for a few years. The unit arrived boxed with a conformance certificate and all the mounting bolts. Installation was straightforward, finished in about 45 minutes. After six months of use on rocky, dry terrain, the housing shows no cracks and the gears run smooth. For the price point, the quality is better than what we were getting from our previous European brand."

Rodrigo Silva, Sugarcane Farm, Brazil
"Our operation in Ribeirao Preto uses flail mowers to chop sugarcane residue after harvest. The conditions are brutal: 40-degree heat, red clay dust everywhere, and thick stalks that put a lot of stress on the gearbox. We installed three CMN-30 units across our fleet at the start of the last season. After about 250 hours each, all three are still running clean with no sign of seal leaks or unusual noise. The 30 HP rating is well matched to our smaller tractors. Good product and fast communication with the CMN sales team when we had questions about bulk pricing."

Antonio Garcia, Landscape Contractor, Spain
"I do landscape and park maintenance around Valencia and go through a lot of flail mower wear parts. The CMN-30 caught my eye because the technical specs matched the gearbox on my Berti mower exactly: same ratio, same input spline, same bolt pattern. Ordered one as a trial and bolted it on without any modification. The finish quality on the housing is better than expected at this price, and the gears mesh quietly. I have already ordered a second one as a backup so I never have to wait for a shipment during peak season."

Ben Walters, Mixed Farm, Australia
"Running a mixed sheep and cropping property near Dubbo, NSW. Got the CMN-30 to replace the original gearbox on a second-hand Fieldmaster flail mower I picked up. The housing dimensions were a near-exact match, just had to drill one mounting hole out by 1 mm. Performance has been spot on for the five months I have used it so far: clean cuts, no vibration, and no oil seeping from the seals. Delivery to Australia took about three weeks from order to door, which was reasonable. Giving it four stars only because I have not had it long enough to judge long-term durability, but everything points to a good run."

James Henderson, Estate Management, United Kingdom
"We look after a 500-acre country estate in Hampshire with a mix of lawns, parkland, and woodland margins. Our flail mower runs off a 25 HP compact tractor, so the 30 HP rating on the CMN-30 gives us a comfortable margin. The gearbox has been on the machine since late spring, and after roughly 150 hours of use it is performing exactly as expected: no leaks, no unusual sounds, and consistent drum speed. Packing and labelling were professional, and the unit arrived with a certificate of conformance. Good product at a fair price."

Additional information

Edited by

Yjx